Parts & Accessories

The Mountain/Urban Recreational Helmet Vent Light is one of the easiest and most powerful ways to increase visibility and safety on the road. Compatible with Fixture MIPS, Verce MIPS, Cormick MIPS, Trella MIPS, and Tremor™ MIPS.

The Sport Recreational Helmet Vent Light is one of the easiest and most powerful ways to increase visibility and safety on the road.

EPR Cheek Pad Replacement Set for Xact Helmet

- Mud and splash protected - Foam padding for additional protection - Simple to access - Can be attached to backpack

Replacement Chin Buckle for Trail RS Helmet

Easily replace the original visor on your iXS Trail RS helmet with this visor. Just bolt it on.

Spare visor and bolts for Trail XC helmet

Spare visor for Trigger AM helmet, including pins

Spare visor and bolts for Trigger FF helmet

Cheek Pad kit for Xact helmet Size SM & ML, 15 & 25mm thickness

Freshen up your iXS Xact helmet with this replacement liner.

Spare cheek pads set for Xult DH helmet

Head lining for Xult DH helmet

Spare visor and bolts for Xult DH helmet

- Replacement charging cable - Used for: Street, Kickstart, Matrix helmets & Lumos remote

- Replacement padding for Kickstart and Kickstart Lite

- Replacement padding for Lumos Matrix and Street helmets

Handlebar mount for Lumos remote

A helmet-mounted taillight is an ideal way to help make sure you are seen in low light conditions. The ATS LED Taillight only fits Lazer helmets equipped with the Advanced Turnfit System. - COMPATIBILITY: Bullet 2.0, Century MIPS, Century, Wasp Air Tri, Victor, Impala MIPS, Impala, Urbanize MIPS - BATTERY TYPE: LR41 button battery - RUN TIME: 37 hours - LUMENS: 4 lumens - ATTACHMENT: ATS dial - WEIGHT: 15g - MATERIAL: Nylon

Keep the rain, snow and mud from getting inside your helmet, or use as a quick aerodynamic solution to close off the front and side vents. Aeroshell is a great accessory for compatible Lazer helmets! The Aeroshell is a plastic cover, designed to fit perfectly over specific models of Lazer helmets. The Aeroshell snaps into place and protects the riders head from wind and rain while still allowing for some air movement under the front of the helmet and out the rear vents. The Aeroshell is unique in that it is easily removed from the helmet when riding conditions are such that additional ventilation is desired. Snap it on when the rain is pouring down and pull it off when the sun starts to shine, the Aeroshell is the perfect tool for every possible condition. Additionally, the Aeroshell provides a significant increase in Aerodynamic performance once it is installed on the helmet. By closing off the ventilation holes, the amount of aerodynamic drag the helmet creates is strongly reduced, making your road helmet into an aero helmet and resulting in a faster ride. - COMPATIBILITY: Blade+ MIPS, Blade+, Blade, Blade MIPS - ATTACHMENT: Blade or Blade+ helmet - WEIGHT: 45g - MATERIAL: Polycarbonate

Keep the rain, snow and mud from getting inside your helmet, or use as a quick aerodynamic solution to close off the front and side vents. Aeroshell is a great accessory for compatible Lazer helmets! The Aeroshell is a plastic cover, designed to fit perfectly over specific models of Lazer helmets. The Aeroshell snaps into place and protects the riders head from wind and rain while still allowing for some air movement under the front of the helmet and out the rear vents. The Aeroshell is unique in that it is easily removed from the helmet when riding conditions are such that additional ventilation is desired. Snap it on when the rain is pouring down and pull it off when the sun starts to shine, the Aeroshell is the perfect tool for every possible condition. Additionally the Aeroshell provides a significant increase in Aerodynamic performance once it is installed on the helmet. By closing off the ventilation holes, the amount of aerodynamic drag the helmet creates is strongly reduced, making your road helmet into an aero helmet and resulting in a faster ride. Sizing: - Small = 52 – 56cm - Medium = 55 – 59cm - Large = 58 – 61cm

Keep the rain, snow and mud from getting inside your helmet, or use as a quick aerodynamic solution to close off the front and side vents. Aeroshell is a great accessory for compatible Lazer helmets! The Aeroshell is a plastic cover, designed to fit perfectly over specific models of Lazer helmets. The Aeroshell snaps into place and protects the riders head from wind and rain while still allowing for some air movement under the front of the helmet and out the rear vents. The Aeroshell is unique in that it is easily removed from the helmet when riding conditions are such that additional ventilation is desired. Snap it on when the rain is pouring down and pull it off when the sun starts to shine, the Aeroshell is the perfect tool for every possible condition. Additionally, the Aeroshell provides a significant increase in Aerodynamic performance once it is installed on the helmet. By closing off the ventilation holes, the amount of aerodynamic drag the helmet creates is strongly reduced, making your road helmet into an aero helmet and resulting in a faster ride. - COMPATIBILITY: Z1 MIPS, Z1 - ATTACHMENT: Z1 helmet - WEIGHT: 45g - MATERIAL: Polycarbonate

Replacement Pads for Lazer's BOB Helmet

Magnetic mount lens for Lazer Bullet 2.0 helmet. The integrated lens is an integral part of the Bullet 2.0 helmet. It can be stored on the helmet surface using the magnetic docking when not in use. - COMPATIBILITY: Bullet 2.0 - ATTACHMENT: magnetic - WEIGHT: 24g - MATERIAL: Polycarbonate

Freshen up the interior of your helmet with a new pad set! Padset details listed below. Replacement padset for Lazer Bullet and Bullet MIPS helmets. Set includes six pads - Two front pads, two top center pads, two top side pads. - COMPATIBILITY: Bullet, Bullet 2.0 - ATTACHMENT: velcro - WEIGHT: 12g - MATERIAL: Foam

Screws for Impala visor. - COMPATIBILITY: Impala MIPS, Impala - WEIGHT: 1g - MATERIAL: Aluminum

Camera mount for Jackal and Impala helmets. - COMPATIBILITY: Jackal MIPS, Jackal, Impala MIPS, Impala - ATTACHMENT: Velcro - WEIGHT: 13g - MATERIAL: Nylon

Keep the ARS fit system clear of debris and serves as a mount for LED taillight accessory. Note: not compatible with LifeBeam accessory. Adds protection to keep ARS retention system clear of debris on Z1 helmet. Also allows the Z-LED or Century LED taillights to be used with the Z1 helmet. - COMPATIBILITY: Z1 - ATTACHMENT: ARS mechanism - WEIGHT: 8g - MATERIAL: Polycarbonate

Freshen up the interior of your helmet with a new pad set! Padset details listed below. Replacement padset for Lazer Cameleon MIPS helmet. Set includes four pads - front pad, two top side pads and top center pad. - COMPATIBILITY: Cameleon MIPS - ATTACHMENT: velcro - WEIGHT: 12g - MATERIAL: Foam

Freshen up the interior of your helmet with a new pad set! - Replacement pads for Jackal helmets